How to Hang a Picture with Picture Hanging Wire: A Comprehensive Guide
Materials You’ll Need:
- Equipment / Tools:
- Phillips head screwdriver
- Nail or awl
- Tape measure
- Pencil
- Wire cutter
- Bubble level
- Materials:
- Picture hanging wire
- 2 D-rings
- 2 adhesive felt or silicone pads
- 2 picture wall hangers
Safety Considerations:
Picture hanging wire weight ratings range from 10 to 50 pounds. Heavy-duty hanging wire can hold up to 150 pounds. Always ensure that you hang your picture within the wire’s weight parameters for safety.
Step-by-Step Instructions:
1. Prepare the Work Area:
Lay the framed picture face-down on a soft cloth or towel. Position the picture so that the top of the picture is facing away from you and the bottom is closest to you. Have your tools nearby.
2. Attach the Bumper Pads:
Remove the protective paper from the back of one felt or silicone pad. Stick the pad on a lower corner of the picture frame, 1/4- to 1/2-inch from the outer edge. Repeat on the other lower corner.
3. Measure the Picture Frame Height and Mark D-Ring Attachment Points:
Use the tape measure to determine the height of the picture frame. Divide the measurement by one-third. For example, if the picture frame is 15 inches tall, one-third of 15 inches is 5 inches. Measure down from the top of the picture frame by 5 inches and make a mark on one side, then repeat on the other side.
4. Create Pilot Holes for the D-Rings:
Create a shallow pilot hole on each of the marks with a pin, awl, or nail. Press hard on the tool and rotate it a couple of times to deepen the hole.
5. Install the D-Rings:
Place one of the D-rings on top of one of the pilot holes, with the flat side of the ring’s attachment base against the picture frame. Rotate the D-ring so that the ring faces sideways. Repeat for the other side.
6. Attach One Side of the Wire:
Slide the end of the picture hanging wire through one of the D-rings, leaving 3 to 4 inches of excess wire. Securely knot the end of the wire on the D-ring, then twist another inch of the excess wire up the rest of the wire and cut off the excess. It’s important to both knot and twist the wire for a secure hold.
7. Attach the Other Side of the Wire:
Pull the wire across the picture frame to the D-ring on the other side. Slide the wire through the D-ring and hold it with one hand. With the other hand, pull the wire up to the top of the picture frame, keeping it taut. Stop the wire 1 to 2 inches before it reaches the top edge of the top rail. Knot and twist the wire on the D-ring.
8. Add the Wall Hangers:
Locate the desired spot on the wall where you want to hang the picture. Use a hammer to nail one of the picture wall hangers to the wall. Add the second wall hanger at the same height as the first hanger, horizontally spaced apart at about one-third to one-half of the width of the picture. For a 10-inch-wide picture, space the two wall hangers about 3 to 5 inches apart.
9. Hang the Picture on the Wall:
Hang the wire first over one wall hanger, then over the adjacent hanger. Tilt the picture up or down to level it. Use a bubble level on top of the picture frame to ensure it’s level, or visually level it relative to room elements.
Tips:
- When vertically placing the picture, remember that the top rail of the picture frame will be 1 to 2 inches higher than the picture hangers.
- For hanging a heavy picture, use heavy-duty hanging wire and ensure that the wall hangers are securely anchored into the wall.
- If you don’t have D-rings, you can use a simple loop of wire or string.
- To hang a picture on a sloped wall, use a wire that is long enough to accommodate the slope and adjust the wall hangers accordingly.
- If you’re hanging a picture on a brick wall, you’ll need to use masonry nails or anchors to secure the wall hangers.